Reset your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a simple process that can be performed in just a few procedures.

• First ensuring your red dot sight is turned on.
• Identify the small reset button on the bottom of the sight.
• Employ a paperclip to press and hold the reset button for approximately 7 seconds.
• Let go the reset button and your Holosun EPS Carry Red Dot sight will restart.
• The red dot sight should now be set back to its factory settings.

Return to Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to return to original, resetting it to default configuration is a breeze. First, find the tiny button on the bottom of your optic. Then, sustain it for around five seconds until you see the indicator light change. Your Holosun EPS Carry is now reset to its factory settings, ready for precise aiming.

restore Your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

• Press and hold the power button for approximately 7 seconds.
• The display will flash, indicating that the reset is successfuly initiated.
• Release the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and confirm your sight's functionality. If you encounter any further problems, don't hesitate to reach out to their technical assistance.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings read more can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

• Beginning with, Activate your Holosun EPS Carry by pressing the power button.
• Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, tap the power button once.
• The display will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Default reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Reinitialized to their default values.

Reinitialize your Holosun EPS Carry through a Factory Original Settings

If your Holosun EPS Carry is acting up, a factory reset might be the answer. This will return your sight to its original settings, clearing any custom configurations you've made. To perform this reset, observe these easy steps:

• First, identify the reset button on your EPS Carry.
• Next, press a thin object, like a pen tip, to activate the reset button.
• While keep the reset switch activated, turn your EPS Carry.
• The sight will flash a message confirming that the reset is complete.

After the reset is complete, your EPS Carry will be set to its factory settings.

Report this wiki page